Payment & Shipping Terms:
|Input Signal:||DMX512(priority) & 0/1-10V||Power Input:||DC12-24V|
|Output Signal:||Constant Voltage PWM Signal||Output Current:||1CH , Max10A|
|Max Power:||120W(12V) / 240W(24V)||Address Setting:||Dip Switch|
|DMX Interface:||RJ45||PWM Socket:||Push Terminals|
|Gross Weight:||220g||Product Size:||L160*W4 *H24 Mm|
led driver dimmer switch,
remote dimmer switch
Max 10A Single Channel DMX512 Decoder & 0/1-10V LED Driver
Model : AL7001 Manual Download: AL7001 .pdf
Thank you for using our DMX512 & 0/1-10V LED driver series. It can be used for both DMX512 lighting control and 0/1-10V LED dimming control. But DMX signal control is preferred for this series of products. It can be controlled by 0/1-10V signal when there is no DMX signal input. Both color changing and brightness adjustment can adopt this products.
AL7001 can be used as DMX decoder or 0/1-10V dimmable driver.It also can be connectted with both DMX512 controller and 0/1-10V dimmer switch at the same,which priority DMX signal control.As we can change color first by DMX512 and then change brightness by 0/1-10V,it realize both color and brightness changing.
1), Meet with the current large scale system many signals output, this product is used for the convenience ofengineering to design.
2), Support DMX signal dimming function and 0/1-10V signal dimmer, priority DMX512 signal dimmer.
3), Single channel constant voltage to control, the max current load ability is 10A.
4), No flicker, analog voltage active 0/1-10V dimmer, passive 0/1-10V dimmer general, can as the main dimming with the large control system.
5), Perfect dimming curve, the traditional 0/1-10V dimmer products, on the vision more than 70% brightness, then after regulation can’t see the LED brightness is still in change . But this product in the design through the chip decoding simulation value , breakthrough the dimming of straight proportion acquisition, and redefine a dimming curve value, do not jitter at low end, high-end is more than 95% of the brightness value still see the obvious change.
6), The product has test function, when has not signal input, the brightness as the maximum output, can through the input interface short circuit to test the product work or not, the input interface short circuit and the brightness will gradually dark to minimum value. When open the circuit it will keep the maximum brightness output.
7), Customizable and 3 years warranty.
|Model No.: AL7001||Control channels: 1CH||Signal Input: DMX512(Priority) & 0/1-10V|
|Input:: DC12-24V||Output: Max 10A||Max Power: 120W(12V)/240W(24V)|
|Frequency: 500HZ||The light gray level: 256||Protection Class: IP40|
|Work Temp.: -20~70℃||Dimension L160*W147*H24(mm)||Gross Weight:: 220g|
Product Size :
1, Product plan, connect the active 0/1-10V voltage regulator, or the passive 0/1-10V dimmer, the LED load and power’s negative and positive with the right interface, open the power supply, dimming the 0/1-10V voltage regulator,so as to change the output of the controller, until getting the satisfactory of LED output. When the ' Analog IN ' port impending. Controller all light output; when the ' Analog IN ' short circuit and the output closed.
2, When DMX signal input, the 1 ~ 10 V analog signal will through the CPU disconnect, priority DMX signal control.
System Wiring Diagram of DMX & 0-10V Driver Series:
1, DMX signal cable is made of twisted pair (line), DMX signal includes positive and negative end, in pressure welding DMX signal line plug should pay special attention to polarity. DMX512 controller input and output interface: signal positive, signal negative, signal ground, please corresponding polarity connection with AL7001.
2, DMX Master output and AL7001's transmission lines can't be over 300 meters.
3, DMX Master(DMX5000) each interface can with not more than 170 pieces of AL7001. Eight output interface.Through the JBLED FLASH light making software and can with computer on line control. Realize infinite contact theDMX lights.
4, When contacted 32 pieces of AL7001, DMX signal must add a signal amplifier such as RE2000. Cascade can't more than4 PCS
5, 0/1-10V simulator dimmer interface signal connection, please choose to surge of smooth curve 0/1-10V dimmers, otherwise may directly affect the smoothness of the LED light
6, The load LED and the controller of power's voltage must be consistent, and must be on the product of the input voltage regulation range.
7, If in a bus and take many pieces of AL7001 dimmer driver, please make sure the dimmer switches with the effective load capacity.
1, Why choose us ?
(1)We are a manufacturer specializing in the R&D of LED Controllers over 8 years in Shanghai .
(2)All our products got the CE , ROHS certificates .
(3)Three years warranty for all products .
(4)OEM/ODM are available for us .
2, How could I pay for it ?
T/T , Western Union ,Paypal and Credit Card are available for payment .
3, How fast can I get these products ?
Usually , samples order within 2-3 working days. Batch order within 5-7working days .
4, What should we do if having problems after receiving your goods ?
Quality is our culture.Strictly inspected before shipping . Once you receivedissatisfied products , please contact us freely in time,we will do our best to deal with .
Contact Person: Andy